YOUR DEFAULT CURRENCY IS

EWP115 Nylon - 24V 115LPM/30GPM Remote Electric Water Pump (PART #8126)

The EWP115 Nylon 24V is available for purchase in following options:

  • Pump Only (Part #8126) 
  • Kit (Part #8026)
  • Combo with Controller (Part #8931)

The EWP®115 (115 litres per minute) pump is suitable for small, medium, large, high- performance and 4WD vehicles. It’s a performance product that improves engine cooling control and capacity whilst giving you more power and torque and improved fuel economy.

 The EWP®115 is a practical alternative to the mechanical belt-driven pump or fitted as an auxiliary pump. Mechanical belt-driven water pumps run directly off the motor and sap engine power … the EWP®115 is hardwired into your electrical system, by-passing the engine and releasing up to an additional 10kw (13hp).

 EWP & CONTROLLER INSTALLATION DEMONSTRATION

 

CONTENTS

DESCRIPTION

UNITS

EWP115 (Nylon) 24V

1

 

 Combined with the LCD EWP®/Fan Digital Controller (See Combo Pack Part #8931), the pump continues to run after you’ve switched off, eliminating “heat soak” and extending engine life.

Davies, Craig’s revolutionary, Australian-designed EWP® pumps are made from anti-corrosive, lightweight nylon reinforced with fibreglass. Universal fit allows for easy mounting into the bottom radiator hose. Our kits come with easy-to-understand DIY instructions and everything you need for easy installation, including different adaptors to fit various hose sizes and all necessary electrical wiring.

An Electric Water Pump is one of the most economical way to increase horsepower and save on fuel consumption whilst caring for your engine.

Used in conjunction with a Davies, Craig EWP® header adaptor kit, it can replace the mechanical water pump completely.

Technical Specifications

 Voltage

24 Volt Pump

Operating voltage

20V DC to 27V DC

Maximum current

5.5A @ 24V

Flow rate (max)

115 L/min (30.38 US gal/min) @ 24V DC

Operating temp.

-40° to 130°C
(-40° to 266°F)

Pump design

Clockwise centrifugal with volute chamber

Pump weight

920 grams (2.03 lb)

Pump material

Nylon 66 - 30% Galss Filled

Burst pressure

500 kPa (72.5 psi)

Seal

Ceramic face seal

Self Priming

No, none of our pumps are self-priming

Fits hose sizes

35mm to 51mm (1⅜” to 2”)

Push on Fittings

Push-On fitting Size

EWP Inlet & Outlet 38mm

  • with 3mm Sleeve (#8510) 44mm
  • with 6mm Sleeve (#8511) 51mm

 

The world’s most advanced total engine cooling management system:


 universal fit

 more power

 more cooling

 increase fuel efficiency

 extend engine life

 world-leading technology

 

EWP® INSTALLATION OPTIONS

Installing an EWP® as an AUXILIARY PUMP

  • Leaving the mechanical water pump in place, install the EWP® into the bottom radiator hose.
  • Remove the thermostat and drill two approx. 3mm (1/8") holes in the thermostat plate to allow some coolant circulation when the thermostat is closed. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.

EWP® INSTALLATION – disabling Mechanical water pump

  • Leaving the mechanical water pump in place, install the EWP® into the bottom radiator hose and remove the manufacturer’s thermostat.
  • You will need to bypass the water pump pulley by installing an appropriate length belt (not supplied). This method makes for an easy installation.
  • If running the pump continuously remove the thermostat and drill two approx. 3mm (1/8") holes in the thermostat plate to allow some coolant circulation. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.

In both these cases, the EWP® will pump past the impeller of the mechanical water pump.

Disengaged mechanical water pump (recommended)

  • Remove the mechanical water pump and remove the thermostat.
  • Then remove the impeller from the mechanical pump shaft. Retain the mechanical water pump using the pump pulley as an idler to avoid re-routing the drive belt.
  • Block any bypass passages and re-install the disengaged water pump ensuring that all gasket surfaces are clean and the new gaskets are properly fitted to prevent leaks.
  • Install the EWPÒ into the bottom radiator hose.

Removed mechanical water pump (Ideal)

  • Remove the mechanical water pump and thermostat from the engine.
  • Install a Davies Craig EWP® Header Adaptor or blanking plate (not supplied). Ensuring the gasket surfaces are clean and the appropriate gasket or sealant is used to prevent leaks.
  • Install the EWP® into the bottom radiator hose. This method will require you to modify or replace the standard radiator hose.
  • Install an appropriate length belt (not supplied) to drive the accessories.

In most cases EWP® will be adequately supported by the radiator hose. Where mounting is required, the EWP® must be soft mounted to protect against vibration. For the EWP115, EWP130 and EWP150 Part #8700 Mounting bracket is recommended.

  

Product Selection Guide

 

Application

 

Pump Model

Pump Kit

Pump Combo

Controller / Switch

Part # 12 V

Part # 24 V

Part# 12 V

Part # 24 V

Part # 12 V

Part # 24 V

Motorbike up to 500cc (Standard)

EBP®15

9001

 

 

 

0444 or 0500

 

 

Motorbike 500cc - 1000cc (Std)

EBP®23

 

9050

 

 

 

 

0444 or 0500

 

 

Motorbike 1000cc - 2000cc (Std)

EBP®25

 

9005

 

 

 

 

0444 or 0500

 

 

Vehicle Heater System (Standard)

EBP®23

 

9050

 

 

 

 

0444 or 0500

 

 

LPG (Butane) System (Standard)

EBP®23

 

9050

 

 

 

 

0444 or 0500

 

 

Intercooler

(depending on capacity)

EBP®23

9050

 

 

 

 

 

EBP®25

9005

 

 

 

 

 

EBP®40

9040

9041

 

 

0444 or 0500

0444 or 0500

EWP®80

8005

 

8807

 

 

 

 

Engines up to 2.0L (Standard)

EWP®80

 

8005

 

 

8807

 

 

8002

 

8002

 

Engines up to 2.0L - 3.5L (Standard)

EWP®115

8025 or

8040

8026 or

8041

8830 or

8850

8831 or

8851

 

8002

 

8002

 

Engines up to 3.5L - 5.0L (Standard)

EWP®130

 

8080

 

8081

 

8890

 

8891

 

8002

 

8002

 

Engines 5.0L or greater (Standard)

EWP®150

 

8060

 

8061

 

8870

 

8871

 

8002

 

8002

Modified Engines

Supercharged/Turbo

EWP®150

 

8060

 

8061

 

8870

 

8871

 

8002

 

8002

 

Drag Racing, Drifting & Speedway

EWP®150

 

8060

 

8061

 

8870

 

8871

 

8002

 

8002

 

Off Road / 4WDs

EWP®130

 

8080

 

8081

 

8890

 

8891

 

8002

 

8002

 

Solar Hot Water Systems (depending on size)

EBP®15

9001

 

 

 

0444 or 0500

 

EBP®23

9050

 

 

 

0444 or 0500

 

EBP®25

9005

 

 

 

0444 or 0500

 

EBP®40

9040

9041

 

 

0444 or 0500

0444 or 0500

 

For further information, see Product Information

User Reviews

  • Be the first to review this product.

Please Login to add your review.