EWP80 Combo - 12V 80LPM/21GPM Remote Electric Water Pump & Controller Combo (Part #8907)
The EWP80 is available for purchase in following options:
The EWP®80 Electric Water Pump and LCD EWP®/Fan Digital Controller Combo – simple, do-it-yourself, easy to install, designed to complement or replace your existing belt-driven, mechanical water pump and engine thermostat, and operate your Thermatic® Fan.
The EWP®80 will fit most vehicle makes and models fitted with naturally-aspirated or turbo engines up to two litres, 12 Volt Only.
Visit the video page for installation demonstration videos: https://daviescraig.com.au/video
Kit Contents | |||
EWP COMPONENTS |
HARDWARE BAG COMPONENTS |
||
Description |
Qty |
Description |
Qty |
EWP Short Kit |
1 |
Scotch Lock |
1 |
EWP & FAN Controller |
1 |
Ring Terminal |
1 |
Inline Adaptor |
1 |
Ring Terminal (Yellow) |
1 |
Wiring Harness (10A Fuse) |
1 |
Self Tap Screws |
1 |
Elbow Adaptor 35mm (Nylon) |
1 |
Temp Sensor Assembly |
1 |
Straight Adaptor 35mm (Nylon) |
1 |
Adaptor M5 Bolt |
6 |
O-Ring |
2 |
Adaptor M5 Nut |
6 |
Rubber Sleeve 3mm (Increase hose fitting size to 38mm) *For larger hose size, you will need 6mm sleeves (Part #18511) which will increase adaptor to fit hose size 41~42mm *not in kit* |
2 |
M5 Cap Screw Long |
6 |
Hose Clamps |
4 |
|
|
EWP Hardware Bag |
1 |
|
Technical Specifications | ||||
Technical Specifications - EWP80 | Technical Specification - LCD Controller | |||
Operating voltage | 3V DC to 15V DC | Voltage range | 12V DC to 29V DC | |
Maximum current | 7.5A @ 13V | Display LCD size |
64.6mm (2.54”) x 55.6mm (2.19”) |
|
Flow rate (max) | 80 L/min (21.13 US gal/min) @ 13V DC | Maximum current | 12Amps | |
Operating temp. | -40° to 130°C (-40° to 266°F) | Warning alarm | High & low Temp., Above set temp., Sensor short circuit, Pump error, High & low voltage and Sensor open circuit | |
Pump design |
Clockwise centrifugal with volute chamber |
Targeted (set) temperatures | Singular degrees from: 40°C (104°F) to 110°C (230°F) |
|
Pump weight | 900 grams (2.0 lb) | Memory | Set & targeted temperature | |
Pump material | Nylon 66, 30% glass-filled | Fan cut-in temp. | 3°C (5.4°F) above the targeted (set) temperature | |
Burst pressure | 350 kPa (50 psi) | Controller type | PCB with micro-processor | |
Seal | Ceramic face seal | Sensor type | Thermister in housing | |
Fits hose sizes | 32mm to 51mm (1⅜” to 2”) | Overrun/ shutdown | -10°C (14°F) below set/target temperature or 3 minutes | |
Self Priming | No, none of our pumps are self-priming | Indicators | Temperature, power, EWP, test, fan, high & low temp, voltage, above set temperature (with alarm) | |
Weight | 100 grams (3.5 oz) | |||
Dimensions |
Length = 98mm (3.8") Width = 95mm (3.7") Depth = 25mm (1”) |
The revolutionary, Australian-designed EWP®80 is made from anti-corrosive, lightweight, heat-resistant, glass-filled nylon and incorporates a ceramic faced seal for long-life durability.
The EWP®80 greatly enhances engine cooling control while giving you added power and improved fuel economy. By removing the parasitic power losses of a belt-driven, mechanical water pump the EWP® can provide up to 10kW (13hp) of extra power and increased torque.
The LCD EWP®/Fan Digital Controller will manage both the EWP® and Thermatic® fan operation. The Digital Controller will vary the speed of the EWP® in response to the engine’s coolant temperature. Multiple temperature settings are provided on the Controller for either maximum power or fuel efficiency.
The Thermatic® Fan/s will be activated automatically once the engine coolant rises 3°C (5.4°F) above the targeted (set) temperature. The Digital Controller will automatically run on for three minutes (or to 10°C / 14°F below the set temperature) after engine shut down, eliminating ‘heat soak’ and extending engine life.
The EWP®80 Digital Controller Combo is supplied in a do-it-yourself kit with everything you need for fitment to your vehicle’s engine, including an easy-to-follow DIY instruction booklet.
The world’s most advanced total engine cooling management system
EWP® INSTALLATION OPTIONS
Installing an EWP® as an AUXILIARY PUMP
EWP® INSTALLATION – disabling Mechanical water pump
In both these cases, the EWP® will pump past the impeller of the mechanical water pump.
Disengaged mechanical water pump (recommended)
Removed mechanical water pump (Ideal)
In most cases EWP® will be adequately supported by the radiator hose. Where mounting is required, the EWP® must be soft mounted to protect against vibration. For the EWP115, EWP130 and EWP150 Part #8700 Mounting bracket is recommended.
Product Selection Guide |
|||||||
---|---|---|---|---|---|---|---|
Application | Pump Model | Pump Kit | Pump Combo | Controller / Switch | |||
Part # 12 V |
Part # 24 V |
Part# 12 V |
Part # 24 V |
Part # 12 V |
Part # 24 V |
||
Motorbike up to 500cc (Standard) | EBP®15 | 9001 | 0444 or 0500 | ||||
Motorbike 500cc - 1000cc (Std) | EBP®23 | 9050 | 0444 or 0500 | ||||
Motorbike 1000cc - 2000cc (Std) | EBP®25 | 9005 | 0444 or 0500 | ||||
Vehicle Heater System (Standard) | EBP®23 | 9050 | 0444 or 0500 | ||||
LPG (Butane) System (Standard) | EBP®23 | 9050 | 0444 or 0500 | ||||
Intercooler (depending on capacity) |
EBP®23 | 9050 | |||||
EBP®25 | 9005 | ||||||
EBP®40 | 9040 | 9041 | 0444 or 0500 | 0444 or 0500 | |||
EWP®80 | 8005 | 8907 | |||||
Engines up to 2.0L (Standard) | EWP®80 | 8005 | 8907 | 8002 | 8002 | ||
Engines up to 2.0L - 3.5L (Standard) | EWP®115 | 8025 or 8040 |
8026 or 8041 |
8930 or 8950 |
8931 or 8951 |
8002 | 8002 |
Engines up to 3.5L - 5.0L (Standard) | EWP®130 | 8080 | 8081 | 8990 | 8991 | 8002 | 8002 |
Engines 5.0L or greater (Standard) | EWP®150 | 8060 | 8061 | 8970 | 8971 | 8002 | 8002 |
Modified Engines Supercharged/Turbo |
EWP®150 | 8060 | 8061 | 8970 | 8971 | 8002 | 8002 |
Drag Racing, Drifting & Speedway | EWP®150 | 8060 | 8061 | 8970 | 8971 | 8002 | 8002 |
Off Road / 4WDs | EWP®130 | 8080 | 8081 | 8990 | 8991 | 8002 | 8002 |
Solar Hot Water Systems (depending on size) | EBP®15 | 9001 | 0444 or 0500 | ||||
EBP®23 | 9050 | 0444 or 0500 | |||||
EBP®25 | 9005 | 0444 or 0500 | |||||
EBP®40 | 9040 | 9041 | 0444 or 0500 | 0444 or 0500 |
For further information, see Product Information