YOUR DEFAULT CURRENCY IS

EWP®115 Nylon Kit Remote Electric Water Pump (12V) (PART #8025)

The EWP®115 Nylon 12V is available for purchase in following options:

  • Pump Only (Part #8125) 
  • Kit (Part #8025) 
  • Combo with Controller (Part #8930)

The EWP®115 pump is suitable for small, medium, large, high- performance and 4WD vehicles. It’s a performance product that improves engine cooling control and capacity whilst giving you more power and torque and improved fuel economy.

 The EWP®115 is a practical alternative to the mechanical belt-driven pump or fitted as an auxiliary pump. Mechanical belt-driven water pumps run directly off the motor and sap engine power … the EWP®115 is hardwired into your electrical system, by-passing the engine and releasing up to an additional 10kw (13hp). Our EWP range are also extensively used in Intercooler Applications.

KIT CONTENTS
PART DESCRPTION UNITS

EWP®115 Nylon 12V

1

EWP® Basic Wiring Harness

1

Hose Clamps

2
RED - Wire Joiner 1
RED - 6mm Ring Terminal 1
RELAY - 12V 40 Amp 5 Pin W/- Resistor Protection 1

SCREW - SELF TAP 8X3/8 BZ

1

 

TECHNICAL SPECIFICATIONS

 Voltage

12 Volt Pump

Operating voltage

3V DC to 15V DC

Maximum current

10A @ 13V

Flow rate (max)

139 L/min (36.7 US gal/min) @ 13V DC

Operating temp.

-40° to 120°C
   (-40° to 248°F)

Pump design

Clockwise centrifugal with volute chamber

Pump weight

920 grams (2.03 lb)

Pump material

Nylon 66 - 30% Galss Filled

Burst pressure

500 kPa (72.5 psi)

Seal

Ceramic face seal

Self Priming

No, none of our pumps are self-priming

Fits hose sizes

35mm to 51mm (1⅜” to 2”)

Push on Fittings

Push-On fitting Size

EWP Inlet & Outlet 38mm

  • with 3mm Sleeve (#8510) 44mm
  • with 6mm Sleeve (#8511) 51mm

 

EWP & CONTROLLER INSTALLATION DEMONSTRATION

 

Combined with an LCD EWP®/Fan Digital Controller (Sold separately Part #8002 or EWP® Combo Pack) will manage both the EWP® and Thermatic® fan operation. The Digital Controller will vary the speed of the EWP® in response to the engine’s coolant temperature. Multiple temperature settings are provided on the Controller for either maximum power or fuel efficiency. The Thermatic® Fan/s will be activated automatically once the engine coolant rises 3°C (5.4°F) above the targeted (set) temperature. The Digital Controller will automatically run on for three minutes (or to 10°C / 14°F below the set temperature) after engine shut down, eliminating ‘heat soak’ and extending engine life. The EWP® Controller Combo Pack is supplied in a do-it-yourself kit with everything you need for fitment to your vehicle’s engine, including an easy-to-follow DIY instruction booklet.

The world’s most advanced total engine cooling management system:


 universal fit

 more power

 more cooling

 increase fuel efficiency

 extend engine life

 world-leading technology

 

EWP® INSTALLATION OPTIONS

Installing an EWP® as an AUXILIARY PUMP

  • Leaving the mechanical water pump in place, install the EWP® into the bottom radiator hose.
  • Remove the thermostat and drill two approx. 3mm (1/8") holes in the thermostat plate to allow some coolant circulation when the thermostat is closed. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.

EWP® INSTALLATION – disabling Mechanical water pump

  • Leaving the mechanical water pump in place, install the EWP® into the bottom radiator hose and remove the manufacturer’s thermostat.
  • You will need to bypass the water pump pulley by installing an appropriate length belt (not supplied). This method makes for an easy installation.
  • If running the pump continuously remove the thermostat and drill two approx. 3mm (1/8") holes in the thermostat plate to allow some coolant circulation. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.

In both these cases, the EWP® will pump past the impeller of the mechanical water pump.

Disengaged mechanical water pump (recommended)

  • Remove the mechanical water pump and remove the thermostat.
  • Then remove the impeller from the mechanical pump shaft. Retain the mechanical water pump using the pump pulley as an idler to avoid re-routing the drive belt.
  • Block any bypass passages and re-install the disengaged water pump ensuring that all gasket surfaces are clean and the new gaskets are properly fitted to prevent leaks.
  • Install the EWPÒ into the bottom radiator hose.

Removed mechanical water pump (Ideal)

  • Remove the mechanical water pump and thermostat from the engine.
  • Install a Davies Craig EWP® Header Adaptor or blanking plate (not supplied). Ensuring the gasket surfaces are clean and the appropriate gasket or sealant is used to prevent leaks.
  • Install the EWP® into the bottom radiator hose. This method will require you to modify or replace the standard radiator hose.
  • Install an appropriate length belt (not supplied) to drive the accessories.

In most cases EWP® will be adequately supported by the radiator hose. Where mounting is required, the EWP® must be soft mounted to protect against vibration. For the EWP®115, EWP®140 and EWP®150 Part #8700 or #8710 Mounting bracket is recommended.

 

PRODUCT SELECTION GUIDE
Electric Water Pump (EWP®)
 APPLICATION

 PUMP 

MODEL

PUMP ONLY PUMP KIT PUMP COMBO
12V 24V 12V 24V 12V 24V
 Engines up to 2.0L
(Standard)
EWP®80 #8105 Nylon
#8106 Flange
#8109 Barb
N/A #8005 Nylon
#8006 Flange
#8009 Barb
N/A #8907 Nylon
#8908 Flange
#8919 Barb
N/A
 Engines up to 2.0L - 3.5L
(Standard)
EWP®115 #8125 Nylon
#8140 Alloy
#8126 Nylon
#8141 Alloy
#8025 Nylon
#8040 Alloy
N/A #8930 Nylon
#8950 Alloy
N/A
 Engines up to 3.5L - 5.0L
(Standard)
EWP®140 #8180 Alloy #8181 Alloy #8080 Alloy N/A #8990 Alloy N/A
Engines 5.0L or greater
 (Standard)

Modified Engines 
Supercharged/Turbo,
Drag Racing, 4WD,
Off Road, Drifting & Speedway
EWP®150 #8160 Sliver
#8165 Black 
#8161 Silver #8060 Silver
#8065 Black
#8061 Silver #8970 Silver
#8975 Black
#8971 Silver
Intercooler
(depending on capacity)
EWP®115 #8125 Nylon
#8140 Alloy
#8126 Nylon
#8141 Alloy
#8025 Nylon
#8040 Alloy
N/A #8930 Nylon
#8950 Alloy
N/A
EWP®140 #8180 Alloy #8181 Alloy #8080 Alloy N/A #8990 Alloy N/A
EWP®150 #8160 Sliver
#8165 Black 
#8161 Silver #8060 Silver
#8065 Black
#8061 Silver #8970 Silver
#8975 Black
#8971 Silver

 

For further information, see Product Information

User Reviews

  • Be the first to review this product.

Please Login to add your review.