YOUR DEFAULT CURRENCY IS

EWP®80 Combo Remote Electric Water Pump & Controller (12V) (Part #8907)

The EWP®80 is available for purchase in following options:

  • Pump Only (Part #8105) 
  • Kit (Part #8005)
  • Combo with Controller (Part #8907)

The EWP®80 Electric Water Pump and LCD EWP®/Fan Digital Controller Combo – simple, do-it-yourself, easy to install, designed to complement or replace your existing belt-driven, mechanical water pump and engine thermostat, and operate your Thermatic® Fan.

The EWP®80 will fit most vehicle makes and models fitted with naturally-aspirated or turbo engines up to two litres, 12 Volt Only.

The revolutionary, Australian-designed EWP®80 is made from anti-corrosive, lightweight, heat-resistant, glass-filled nylon and incorporates a ceramic faced seal for long-life durability.


The EWP®80 greatly enhances engine cooling control while giving you added power and improved fuel economy. By removing the parasitic power losses of a belt-driven, mechanical water pump the EWP® can provide up to 10kW (13hp) of extra power and increased torque and used extensively in Intercooler applications.

COMBO CONTENTS
PART DESCRPTION UNITS
EWP®80 - Nylon 12V Assembly 1
Nylon Flange Adapter: 35mm Straight 1
Nylon Flange Adapter: 35mm 90° Elbow 1
Adapter - Rubber Sleeve - 3mm {1/8"} 4
HOSE CLAMP (WD9 40-60 W2) EWP (1110020130) 4
EWP ADAPTER O-RING 2
Wiring Harness - EWP & Fan controller : suits 8020, 8000, 8001 & 8002 1
EWP®/Fan Digital controller 1
Adaptor - Nylon - In Line, 35mm (2 x 1/4" NPT) 1
1/4" NPT Nylon - Bung 1
U-Bracket - For #8002 1
Mounting Plate - For #8002 1
SCREW - SELF TAP 8X3/8 BZ 1
BLUE 6mm Ring Terminal 1
5x12 Flanged Hex Set Screw Zinc Silver 6
5x16 Flanged Hex Set Screw Zinc Silver/ 6
M5 FLANGE NUT ZINC SILVER 6
Sensor Thermal - coolant  temp - ¼" NPT thread 1

 

TECHNICAL SPECIFICATIONS
EWP®80 - ELECTRIC WATER PUMP      LCD CONTROLLER
Operating voltage 3V DC to 15V DC Voltage range 12V DC to 29V DC
Maximum current 7.5A @ 13V Display LCD size

64.6mm (2.54”) x 55.6mm (2.19”)

Flow rate (max) 90 L/min (23.8 US gal/min) @ 13V DC Maximum current 12Amps
Operating temp. -40° to 120°C (-40° to 248°F) Warning alarm High & low Temp., Above set temp., Sensor short circuit, Pump error, High & low voltage and Sensor open circuit
Pump design

Clockwise centrifugal with volute chamber

Targeted (set) temperatures Singular degrees from:
40°C (104°F) to 110°C (230°F)
Pump weight 900 grams (2.0 lb) Memory Set & targeted temperature
Pump material Nylon 66, 30% glass-filled Fan cut-in temp. 3°C (5.4°F) above the targeted (set) temperature
Burst pressure 350 kPa (50 psi) Controller type PCB with micro-processor
Seal Ceramic face seal Sensor type Thermister in housing
Fits hose sizes 32mm to 51mm (1⅜” to 2”) Overrun/ shutdown -10°C (14°F) below set/target temperature or 3 minutes
Self Priming No, none of our pumps are self-priming Indicators Temperature, power, EWP, test, fan, high & low temp, voltage, above set temperature (with alarm)
    Weight 100 grams (3.5 oz)
Dimensions

Length = 98mm (3.8")

Width = 95mm (3.7")

Depth = 25mm (1”)

   

EWP & CONTROLLER INSTALLATION DEMONSTRATION

 

Combined with an LCD EWP®/Fan Digital Controller will manage both the EWP® and Thermatic® fan operation. The Digital Controller will vary the speed of the EWP® in response to the engine’s coolant temperature. Multiple temperature settings are provided on the Controller for either maximum power or fuel efficiency. The Thermatic® Fan/s will be activated automatically once the engine coolant rises 3°C (5.4°F) above the targeted (set) temperature. The Digital Controller will automatically run on for three minutes (or to 10°C / 14°F below the set temperature) after engine shut down, eliminating ‘heat soak’ and extending engine life. The EWP® Controller Combo Pack is supplied in a do-it-yourself kit with everything you need for fitment to your vehicle’s engine, including an easy-to-follow DIY instruction booklet.

The world’s most advanced total engine cooling management system:


 universal fit

 more power

 more cooling

 increase fuel efficiency

 extend engine life

 world-leading technology

 

EWP® INSTALLATION OPTIONS

Installing an EWP® as an AUXILIARY PUMP

  • Leaving the mechanical water pump in place, install the EWP® into the bottom radiator hose.
  • Remove the thermostat and drill two approx. 3mm (1/8") holes in the thermostat plate to allow some coolant circulation when the thermostat is closed. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.

EWP® INSTALLATION – disabling Mechanical water pump

  • Leaving the mechanical water pump in place, install the EWP® into the bottom radiator hose and remove the manufacturer’s thermostat.
  • You will need to bypass the water pump pulley by installing an appropriate length belt (not supplied). This method makes for an easy installation.
  • If running the pump continuously remove the thermostat and drill two approx. 3mm (1/8") holes in the thermostat plate to allow some coolant circulation. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.

In both these cases, the EWP® will pump past the impeller of the mechanical water pump.

Disengaged mechanical water pump (recommended)

  • Remove the mechanical water pump and remove the thermostat.
  • Then remove the impeller from the mechanical pump shaft. Retain the mechanical water pump using the pump pulley as an idler to avoid re-routing the drive belt.
  • Block any bypass passages and re-install the disengaged water pump ensuring that all gasket surfaces are clean and the new gaskets are properly fitted to prevent leaks.
  • Install the EWPÒ into the bottom radiator hose.

Removed mechanical water pump (Ideal)

  • Remove the mechanical water pump and thermostat from the engine.
  • Install a Davies Craig EWP® Header Adaptor or blanking plate (not supplied). Ensuring the gasket surfaces are clean and the appropriate gasket or sealant is used to prevent leaks.
  • Install the EWP® into the bottom radiator hose. This method will require you to modify or replace the standard radiator hose.
  • Install an appropriate length belt (not supplied) to drive the accessories.

In most cases EWP® will be adequately supported by the radiator hose. Where mounting is required, the EWP® must be soft mounted to protect against vibration. For the EWP®115, EWP®140 and EWP®150 Part #8700 or #8710 Mounting bracket is recommended.

 

PRODUCT SELECTION GUIDE
Electric Water Pump (EWP®)
 APPLICATION

 PUMP 

MODEL

PUMP ONLY PUMP KIT PUMP COMBO
12V 24V 12V 24V 12V 24V
 Engines up to 2.0L
(Standard)
EWP®80 #8105 Nylon
#8106 Flange
#8109 Barb
N/A #8005 Nylon
#8006 Flange
#8009 Barb
N/A #8907 Nylon
#8908 Flange
#8919 Barb
N/A
 Engines up to 2.0L - 3.5L
(Standard)
EWP®115 #8125 Nylon
#8140 Alloy
#8126 Nylon
#8141 Alloy
#8025 Nylon
#8040 Alloy
N/A #8930 Nylon
#8950 Alloy
N/A
 Engines up to 3.5L - 5.0L
(Standard)
EWP®140 #8180 Alloy #8181 Alloy #8080 Alloy N/A #8990 Alloy N/A
Engines 5.0L or greater
 (Standard)

Modified Engines 
Supercharged/Turbo,
Drag Racing, 4WD,
Off Road, Drifting & Speedway
EWP®150 #8160 Sliver
#8165 Black 
#8161 Silver #8060 Silver
#8065 Black
#8061 Silver #8970 Silver
#8975 Black
#8971 Silver
Intercooler
(depending on capacity)
EWP®115 #8125 Nylon
#8140 Alloy
#8126 Nylon
#8141 Alloy
#8025 Nylon
#8040 Alloy
N/A #8930 Nylon
#8950 Alloy
N/A
EWP®140 #8180 Alloy #8181 Alloy #8080 Alloy N/A #8990 Alloy N/A
EWP®150 #8160 Sliver
#8165 Black 
#8161 Silver #8060 Silver
#8065 Black
#8061 Silver #8970 Silver
#8975 Black
#8971 Silver

 

For further information, see Product Information

User Reviews

  • Be the first to review this product.

Please Login to add your review.