YOUR DEFAULT CURRENCY IS

EWP80 - 12V 80LPM/21GPM REMOTE ELECTRIC WATER PUMP (12V) (PART #8105)

The EWP80 is available for purchase in following options:

  • Pump Only (Part #8105) 
  • Kit (Part #8005)
  • Combo with Controller (Part #8907)

The EWP®80 Electric Water Pump – simple, do-it-yourself, easy to install, designed to complement or replace your existing belt-driven, mechanical water pump. It will fit most vehicle makes and models fitted with naturally-aspirated or turbo engines up to two litres. The revolutionary, Australian-designed EWP®80 is made from anti-corrosive, lightweight, heat-resistant, glass-filled nylon and incorporates a ceramic faced seal for long-life durability.


The EWP®80 greatly enhances engine cooling control while giving you added power and improved fuel economy. By removing the parasitic power losses of a belt-driven, mechanical water pump the EWP® can provide up to 10kW (13hp) of extra power and increased torque.

EWP & CONTROLLER INSTALLATION DEMONSTRATION

 

EWP80 CONTENTS   
Description Quantity
EWP80 Pump 12V 1
5x12 Flanged Hex Set Screw Zinc Silver 6
5x16 Flanged Hex Set Screw Zinc Silver 6
M5 FLANGE NUT ZINC SILVER 6

 

Technical Specifications
Voltage 12 Volt Pump
Operating voltage 3V DC to 15V DC
Maximum current 7.5A @ 13V
Flow rate (max) 80 L/min (21.13 US gal/min) @ 13V DC
Operating temp. -40° to 130°C  (-40° to 266°F)
Pump design Clockwise centrifugal with volute chamber
Pump weight 900 grams (2.0 lb)
Pump material Nylon 66, 30% glass-filled
Burst pressure 350 kPa (50 psi)
Seal Ceramic face seal
Self Priming No, none of our pumps are self-priming
Fits hose sizes 32mm to 51mm (1⅜” to 2”)

 

Combined with an LCD EWP®/Fan Digital Controller (Sold separately Part #8002 or combo #8907) will manage both the EWP® and Thermatic® fan operation. The Digital Controller will vary the speed of the EWP® in response to the engine’s coolant temperature. Multiple temperature settings are provided on the Controller for either maximum power or fuel efficiency. The Thermatic® Fan/s will be activated automatically once the engine coolant rises 3°C (5.4°F) above the targeted (set) temperature. The Digital Controller will automatically run on for three minutes (or to 10°C / 14°F below the set temperature) after engine shut down, eliminating ‘heat soak’ and extending engine life. The EWP®80 Digital Controller Combo is supplied in a do-it-yourself kit with everything you need for fitment to your vehicle’s engine, including an easy-to-follow DIY instruction booklet.

The world’s most advanced total engine cooling management system:


 universal fit

 more power

 more cooling

 increase fuel efficiency

 extend engine life

 world-leading technology

lightweight Nylon

 

EWP® INSTALLATION OPTIONS

Installing an EWP® as an AUXILIARY PUMP

  • Leaving the mechanical water pump in place, install the EWP® into the bottom radiator hose.
  • Remove the thermostat and drill two approx. 3mm (1/8") holes in the thermostat plate to allow some coolant circulation when the thermostat is closed. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.

EWP® INSTALLATION – disabling Mechanical water pump

  • Leaving the mechanical water pump in place, install the EWP® into the bottom radiator hose and remove the manufacturer’s thermostat.
  • You will need to bypass the water pump pulley by installing an appropriate length belt (not supplied). This method makes for an easy installation.
  • If running the pump continuously remove the thermostat and drill two approx. 3mm (1/8") holes in the thermostat plate to allow some coolant circulation. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.

In both these cases, the EWP® will pump past the impeller of the mechanical water pump.

Disengaged mechanical water pump (recommended)

  • Remove the mechanical water pump and remove the thermostat.
  • Then remove the impeller from the mechanical pump shaft. Retain the mechanical water pump using the pump pulley as an idler to avoid re-routing the drive belt.
  • Block any bypass passages and re-install the disengaged water pump ensuring that all gasket surfaces are clean and the new gaskets are properly fitted to prevent leaks.
  • Install the EWPÒ into the bottom radiator hose.

Removed mechanical water pump (Ideal)

  • Remove the mechanical water pump and thermostat from the engine.
  • Install a Davies Craig EWP® Header Adaptor or blanking plate (not supplied). Ensuring the gasket surfaces are clean and the appropriate gasket or sealant is used to prevent leaks.
  • Install the EWP® into the bottom radiator hose. This method will require you to modify or replace the standard radiator hose.
  • Install an appropriate length belt (not supplied) to drive the accessories.

In most cases EWP® will be adequately supported by the radiator hose. Where mounting is required, the EWP® must be soft mounted to protect against vibration. For the EWP115, EWP130 and EWP150 Part #8700 Mounting bracket is recommended.

 

 

Product Selection Guide

Application Pump Model Pump Kit Pump Combo Controller / Switch
Part #
12 V
Part #
24 V
Part#
12 V
Part #
24 V
Part #
12 V
Part #
24 V
Motorbike up to 500cc (Standard) EBP®15 9001       0444 or 0455  
Motorbike 500cc - 1000cc (Std) EBP®23 9050       0444 or 0455  
Motorbike 1000cc - 2000cc (Std) EBP®25 9005       0444 or 0455  
Vehicle Heater System (Standard) EBP®23 9050       0444 or 0455  
LPG (Butane) System (Standard) EBP®23 9050       0444 or 0455  
Intercooler
(depending on capacity)
EBP®23 9050          
EBP®25 9005          
EBP®40 9040 9041     0444 or 0455 0444 or 0455
EWP®80 8005   8907      
Engines up to 2.0L (Standard) EWP®80 8005   8907   8002 8002
Engines up to 2.0L - 3.5L (Standard) EWP®115 8025 or
8040
8026 or
8041
8930 or
8950
8931 or
8951
8002 8002
Engines up to 3.5L - 5.0L (Standard) EWP®130 8080 8081 8990 8991 8002 8002
Engines 5.0L or greater (Standard) EWP®150 8060 8061 8970 8971 8002 8002
Modified Engines
Supercharged/Turbo
EWP®150 8060 8061 8970 8971 8002 8002
Drag Racing, Drifting & Speedway EWP®150 8060 8061 8970 8971 8002 8002
Off Road / 4WDs EWP®130 8080 8081 8990 8991 8002 8002
Solar Hot Water Systems (depending on size) EBP®15 9001       0444 or 0455  
EBP®23 9050       0444 or 0455  
EBP®25 9005       0444 or 0455  
EBP®40 9040 9041     0444 or 0455 0444 or 0455

  

 For further information, see Product Information

User Reviews

  • Be the first to review this product.

Please Login to add your review.